Direct steam injection (DSI) is an emerging technology for municipal biosolids heating, especially in processes that use anaerobic digestion.
DSI has a long track record in challenging slurry heating applications. Steam is readily available and can be inexpensive to produce. Scaling from small to large flows with steam is effective and reliable.
When applied correctly, DSI provides significant process benefits and overcomes a number of limitations that go with conventional solids heating methods.
Heating in anaerobic digestion
Most wastewater treatment plants with flows above 5 mgd use anaerobic solids digestion. Microbes in the digester break down the organic material, producing methane that can be captured to power boilers and electric generator sets.
Unlike aerobic digestion, which operates at ambient conditions, anaerobic digestion operates at higher temperatures to stimulate microbial activity and accelerate the biological process. To achieve higher operating temperatures, heat must be added to the process, and the temperature of the digester must be maintained.
The operating temperature balance is critical for sustaining the correct biological environment in an anaerobic digester. Both acid former and methane former microbes optimize their processing capacity at stable temperatures. Meso-philic digestion is optimum at 95 degrees F and thermophilic digestion at 131 degrees F.
Precise temperature control provides the ideal environment. Solids can be heated before delivery to the digester and then recirculated through a heater to maintain the ideal processing temperatures.
One challenge present when heating municipal solids is the heat-sensitive nature of the material. The media used in solids heating generally is limited to 150 degrees F to avoid scorching and fouling. Municipal solids also tend to have high viscosity, which can cause large pressure drops and put excessive demand on feed pumps. Higher-viscosity solids also make it challenging to provide uniform heating, free of hot spots.
How DSI works
Early attempts at DSI heating in anaerobic digestion commonly used steam sparge devices, which have a fixed steam exit area and use an external control valve to adjust the steam flow. These systems experienced problems with hammer and vibration, leading to unstable operation and poor temperature control.
One key factor in successful DSI is to maintain high steam velocity for effective mixing and condensation of the steam into the solids. High velocity is maintained by altering the exit area of the steam, rather than adjusting the steam pressure, to adjust steam mass flow. This approach is known as internal modulation to achieve choked flow.
Choked flow is the phenomenon of accelerating a vapor to sonic velocity by creating a pressure differential through an engineered nozzle. When choked flow is established, the steam mass flow can be metered to precisely control the heating of the slurry. This produces predictable results based on the position of the stem-plug.
Through a variable-area steam diffuser, steam flow is metered at the point where steam and liquid first contact and mix. This method eliminates the need for an external steam control valve or downstream mechanical mixing devices.
Selecting a DSI heater
In choosing a DSI heater for solids, the first and most important factor is the need for a differential between the steam pressure and the liquid pressure. DSI heater operation is optimized by maintaining high steam velocity to drive the condensation of the steam and transfer energy in a stable and rapid manner. The pressure differential determines the velocity of the steam.
Steam injectors that use an external steam-pressure regulating valve need to operate with the liquid pressure at less than 60 percent of the absolute steam pressure. In externally controlled heaters, the steam pressure is substantially reduced through the steam-control valve, so the available steam pressure is much lower than the design pressure. Reduction of the steam pressure also reduces steam velocity, leading to poor steam condensation and process upsets.
A second critical factor is to maintain a minimum differential between the steam pressure and the liquid pressure. This condition presents fewer process upsets, leading to more stable DSI heater operation (free of hammer and vibration), better pump integration, and improved temperature control. All these can be optimized by maintaining high-velocity steam injection to promote rapid and complete steam condensation.
A jet diffuser heater design using internal steam control allows the steam and liquid pressures to be much closer while still providing high-velocity steam injection. The ability to operate with liquid pressures up to 80 percent of the absolute steam pressures allows for stable operation across a wide operating range, minimizing process upsets.
There are a variety of ways to achieve the desired condition in real-world applications. The first is to choose a steam supply of sufficient pressure to meet the requirements. The second is to reduce the liquid pressure by moving the heater to a higher elevation, trimming the pump impellers, or changing the pressure settings in the control loops — or some combination of these.
Another essential factor for DSI heating is maintaining high-velocity steam (
